Alarm Lock NETWORXPANEL Specifikace stáhnout pdf (Strana 2)

Operating Temperature: 14-120°F (–10-49°C)

Input Power: 16.5VAC via Class 2 Plug-In 50VA

Transformer (supplied model TRF-14)

Maximum Lock Power Output Current: 1.5A @

12VDC

Maximum Wiegand Power Output Current: 250mA

@ 12VDC

Maximum Wiegand Red and Green LED Current:

20mA each output

Maximum Sounder Current: 100mA

Maximum Keypad Power Output Current: 200mA

@ 12VDC

Primary and Secondary Relays: SPDT Form C, N/

O, N/C 8A @ 30VAC or VDC

Supplied Backup Battery: Sealed Lead Acid 4AH

Battery Backup Time: Approximately 2 hours at full

load

NETDK / NETPDK Networx Keypads

Power Requirements: 12VDC supplied by NET-

WORXPANEL

Idle Current: 10mA

Maximum Wire Length: 200 feet (61m)

Recommended Wire Size: 24 AWG minimum

Proximity Card Formats Supported: Alarm Lock

standard 36 bit format or HID standard 26 bit format

(for use with the model NETPDK only)

WIEGAND DATA FORMATS SUPPORTED

The NETWORXPANEL Wiegand inputs (terminals T4-

T8) are compatible with all Wiegand devices that out-

put their data in a "data1 / data0" format. If you are un-

sure of the compatibility of your Wiegand device data

format, call Alarm Lock customer service (have your

DL-Windows software version number available when

calling).

Wiegand Devices Supported

The NETWORXPANEL control panel has been tested

to work with the following Wiegand device models:

• HID Classic Swipe Wiegand Reader Model 310

(Continental 36-bit card format compatible).

• HID ProxPro with Keypad Model 5355

• HES model RF5910 Hybrid Electric Strike with

HID125k reader

Note that other Wiegand device models not tested may

also be fully compatible. For more information, see the

section "ENROLLING WIEGAND SWIPE CARDS" fur-

ther in this manual.

LED AND BUTTON DESCRIPTIONS

The NETWORXPANEL PC board contains two LED's

and 1 button, as follows:

(LD1) Activity LED: Green LED located on the right

side of the PC board; flickers during keypad data

transfer.

(LD2) AC Power LED: Located on the left side of the

PC board, this LED lights when the panel is powered

(AC is present).

(S2) Reset Button: Located on the right side of the PC

board; press and hold for 15 seconds to clear the

NETWORXPANEL memory. Note: When memory is

cleared, the green LD1 LED will flash once every sec-

ond for 5 seconds. In addition, all keypad and device

LED's will flash once every second in unison. The

keypad sounders and device sounders (if so

equipped) will also sound in unison with the LED

flashes.

Note: Although the Reset button will clear all NET-

WORXPANEL memory, if two NETPDK or NETDK

keypads are wired to the NETWORXPANEL, the pri-

mary and secondary keypad designations will NOT

be cleared; this keypad identification data is stored

within the memory located inside the keypad itself.

See the section "Designate Primary and Secondary

Keypads" for the operation of this feature.

TERMINAL DESCRIPTIONS

From left to right, the PC board terminals are as follows:

(T1) EGND: Wire earth ground using a No. 16 AWG. or

larger wire to a metal cold-water pipe. Do not use a

gas pipe, plastic pipe or AC ground connections.

NOTE: Grounding connections should avoid bends in

the grounding wire whenever possible.

(T2-T3) AC IN: Connect to the supply 16.5VAC trans-

former. Use 16AWG wire for shorter runs, and use

14AWG for longer runs. 25 feet maximum.

(T4-T8) WIEGAND INPUTS

Two Wiegand devices are supported on the input ter-

minals as detailed below.

(T4) WOA: If one Wiegand device is used, do not con-

nect any wires to this terminal; use the WO terminal

below.

If two Wiegand devices are used, connect the "Data

0" wire from the second Wiegand device to this termi-

nal, (connect the "Data 0" wire from the first Wiegand

device to the WO terminal).

(T5) WO: If one Wiegand device is used, connect the

"Data 0" wire to this terminal.

If two Wiegand devices are used, connect the "Data

0" wire from the first Wiegand device to this terminal

(connect the "Data 0" wire from the second Wiegand

device to the WOA terminal).

(T6) W1: If one Wiegand device is used, connect the

"Data 1" wire to this terminal.

If two Wiegand devices are used, connect both Wie-

1 2 3 4 5 6 7 ... 11 12

Komentáře k této Příručce

Žádné komentáře

Alarm Lock NETWORXPANEL Specifikace Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Alarm Lock NETWORXPANEL