Alarm Lock Trilogy DL3500 Manuál s instrukcemi stáhnout pdf (Strana 34)

ACCESS = Entry into a restricted area.

AMBUSH = A special Code entered at the keypad when the User is

forced to unlock a device. The device unlocks but sends a silent

alarm with no indication at the keypad. Can be used to trip a re-

lay, to alert security, or trip a silent alarm on a Burglary Control

Panel.

AUDIT TRAIL = A date/time stamped log of previous lock events.

BURGLARY CONTROL PANEL = Provides local alarm and remote

communication to request security for burglary/break-in. A

DL4500 relay output used for Ambush can provide a silent alarm

and call-for-help.

CLOCK

• REAL TIME CLOCK = An accurate built-in clock that allows date/

time stamping of events. The clock can be slowed or speeded up to

fine tune long term accuracy to within three minutes per year.

• CLOCK SETTINGS = Printout includes date, time, weekday, and

clock speed.

• CLOCK SPEED = The clock can be adjusted to allow faster/slower

speeds and therefore increasing clock accuracy.

CODE = Numeric sequence of numbers (such as: 1234) entered at

the keypad. If Star-Enter-Key is required, must be followed by a

[:] key.

• AMBUSH CODE = See Ambush.

• BASIC USER CODE = User Codes assigned to User Num-

bers 12+ (except Users 297-300). (Does not allow

programming)

• INSTALLER CODE = User Codes assigned to User Numbers

2 and 3. (Allows all programming except Master functions).

• INVALID CODE = A User Code that has not been

programmed in the lock.

• MANAGER CODE = User Codes assigned to User Numbers 4

through 6. (Allows most of the programming functions).

• MASTER CODE = User Code assigned to User Number 1.

Default (factory) Master Code is 123456. The User with the

Master Code has complete control of the lock.

• PRINT ONLY USER CODE = User Code assigned to Users

10 and 11. (Allows no programming except print functions).

• QUICK ENABLE USER 300 CODE = Refers to the User Code

entered by User 297 which (when entered at the keypad) en-

ables the User Code assigned to User 300 for one time only.

• QUICK PC ACCESS CODE = Permits upload/download to

DL-Windows Software on IBM/compatible computer running

Microsoft Windows 95, 98, or NT 4.0. Refers to the User Code

for User 298.

• SERVICE CODE = User 300 User Code. Allows only one

entry, then needs to be re-enabled by the User 297 User Code

to regain access.

• SUPERVISOR CODE = User Codes assigned to Users 7, 8

and 9. Can only program day-to-day operation.

• USER CODE = Code used by Users. Code is 3 to 6 numeric

digits long, allowing controlled entry.

• VALID CODE = An entered User Code that has been

programmed in the device.

COM PORT = A computer serial communications port used to

communicate with the Lock and/or Data Transfer Module.

DATA TRANSFER MODULE = A device that permits transfer of

program/data between a computer and the lock.

DATE = Month, Day and Year entered as MMDDYY.

DAY OF WEEK = Sunday through Saturday (where 1 = Sunday and 7

= Saturday).

DEFAULT = Default settings are the original settings that were set at

the factory; in other words, it is the lock's original factory condition

when the lock was first taken out of its box. The default settings

are permanently encoded within the lock's fixed memory, and

when the lock is first started, or when power is removed and re-

applied (see Wiring and Power-Up, page 11), the original factory

default settings are re-loaded and take effect.

DISABLE = Turn off.

DOOR NUMBER = Identification of each door lock with a specific

number in order to ensure that the correct lock is associated with

the correct lock program within DL-Windows or the AL-DTM.

Note: "Door Number" is a term used with AL-DTM versions 1 and

2 and with DL-Windows versions 3.5.0 and earlier. Later versions

of the AL-DTM and DL-Windows monitor door numbers automati-

cally, therefore there is no need to manually change door numbers

via the keypad. Therefore, Function 59 is no longer used with the

later versions of the AL-DTM and DL-Windows. See page 23,

Function 59 for more information.

DOWNLOAD = Send data to lock or AL-DTM.

ENABLE = Turn on.

EVENTS = Recorded lock activity.

FUNCTION (also called Programming Functions) = are the numbers

used to program lock features (enabling/disabling Users, User

Groups, Passage Mode, Schedules, etc.).

GROUP

• USER GROUP = Defining a User to specific Groups, allows

User entry when the Group is allowed entry.

• GROUP 1 DISARMS BURGLAR CONTROL = A Group 1

USER CODE entry can disarm an alarm panel during a

predefined schedule. Should the Group 1 enter the lock

outside of the scheduled time, the alarm will not disarm. The

Glossary

1 2 ... 29 30 31 32 33 34 35 36

Komentáře k této Příručce

Žádné komentáře

Alarm Lock Trilogy DL3500 Manuál s instrukcemi Strana 34

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Alarm Lock Trilogy DL3500