Alarm Lock Trilogy PDK3000 Series Manuál s instrukcemi stáhnout pdf (Strana 11)

WIRING

See the Installation Manual for detailed illustrations and

additional information.

External Power:

Red / Black wires - External 12-24 Volts AC or DC

Power Source.

Remote Input:

White / White wires - Wire a Normally Open Contact

to wires (white and white). Momentarily close to allow

the device to unlock the door and allow entry. NOTE:

Remote Input is enabled from the factory.

(See

page 26)

Main/Entry Relay:

The Main Relay (also called the Entry Relay) is, for

example, used to operate a door strike to allow ac-

cess through a door.

COM-Purple / NO-Gray / NC-Blue - See page 27

(Function 67) for programming options for this relay.

Auxiliary Relay:

The Auxiliary Relay is an additional relay used to con-

trol cameras, lights, an audible sounder, etc.

COM-Black / NO-Pink / NC-White - See page 27

(Function 67) for programming options for this relay.

Wiring to Disarm a Burglary Control Panel

Burglary Control Panel wiring. See page 30.

POWER UP

• When applying power to the lock for the first time, stop

and follow the procedure outlined in "Quick Start, First time

Power Up" further in this manual.

• When power is re-applied to a lock that was already op-

erational, proceed as follows:

1. Disconnect battery pack connector.

2. With battery power disconnected, press and hold

down

; for 10 seconds to insure discharge of all ca-

pacitors.

3. Re-connect battery pack (lock will sound 3 short beeps). If

beeps are not heard, then restart at step 1.

4. Do not press any keys for 15 seconds.

5. After 15 seconds, the LED will flash red 6 times and 6

beeps will sound.

The lock is now ready for use. The pre-existing program is

loaded from fixed memory. Set the clock using functions 38,

39 and 40.

ERASE ALL PROGRAMMING

(The "out of box" factory default will be loaded)

1. Remove the battery pack.

2. With battery power disconnected, press and hold

down

; for 10 seconds to ensure discharge of all ca-

pacitors.

3. Re-install the battery pack (lock will sound 3 short beeps).

If beeps are not heard, then restart at step 1.

4. Within 5 seconds after hearing the 3 short beeps, press

and hold

; until the lock begins to beep, then release.

5. A series of 5 RED LED and 5 beeps will be heard followed

by 10 seconds of silence, then 3 GREEN LEDs and 3 fast

beeps.

All settings and programming have been erased and the lock

is now ready for use. Note: All lock programming can also be

erased (without need to disconnect the batteries) by entering

Function 99.

SPECIFICATIONS

Operating Voltage Range: 10V - 28V AC or DC

For uninterrupted operation, a power source that pro-

vides battery backup is required.

12V Current Consumption

Idle Current: 3ma

Maximum Current: 55ma

24V Current Consumption

Idle Current: 7ma

Maximum Current: 80ma

2 Relays:

SPDT Form C, N/O, N/C, C

8 amps @ 24V AC or DC

24 Volts MAXIMUM

Wiring, Power Up and Specifications

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 39 40

Komentáře k této Příručce

Žádné komentáře

Alarm Lock Trilogy PDK3000 Series Manuál s instrukcemi Strana 11

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Alarm Lock Trilogy PDK3000 Series