Alarm Lock ETPLN Uživatelská příručka stáhnout pdf (Strana 22)

22 DL-WINDOWS™ for Trilogy Networx™ V4.0 USER'S GUIDE

Normal Tasks

DL-WINDOWS TASKS

Add a new lock Profile to an Account

Adding a new lock Profile is a common task in Dl-

Windows, usually performed after creating a new Ac-

count. See page 15, step 1 ("Create a new Account")

and step 2 ("Create new virtual lock Profiles") for step-

by-step instructions.

Delete a lock Profile from an Account

Open the DL-Windows main screen and find the Ac-

count Tree "white box" area listing lock Profiles. Simply

right-click the Profile and click Delete Lock Profile.

Note: Performing this action (clicking Delete Lock Pro-

file) does not remove programming from the physical

lock because communication between DL-Windows and

the physical lock does not actually occur.

REPLACING HARDWARE

Replacing an existing Router

Remove the existing router and install either a wired

or wireless router as described in its instructions.

For the connection between the computer and the

router, most laptops and some desktop computers con-

tain a wireless network card (also called a "wireless net-

work interface controller") to allow for wireless communi-

cation between your computer and a wireless router; if

your computer does not have a wireless network card,

you can usually connect the "non-wireless" network card

in your computer to the router using an RJ-45 Ethernet

cable.

For the connection from the router to the network,

the router is plugged into an Ethernet network source --

usually either a modem or a wall jack. As shown in the

overview drawing on page 3, with "Large Networks" the

computer may be connected directly to the network

(usually just a wall jack) with an RJ-45 Ethernet cable.

Note: If the computer is connected directly to the net-

work via a wall jack, the Gateway module may also be

connected directly to the network (for example, via an-

other wall jack) at any location within the premises.

Click the GW Confg button to open the Gateway Con-

figuration screen. Click Tools, Select Network

Adapter. The Network Adapter Selection screen that

appears allows you to identify the Ethernet "network in-

terface card" (NIC) you are using inside your computer

to communicate with the Gateway devices in your sys-

tem. Some computers have a printed circuit board that

plugs into the motherboard, other computers have the

network adapter (Ethernet) built into the motherboard,

thus precluding the need for a separate Ethernet card.

Remember, the router or corporate Ethernet network is

connected to this Ethernet adapter with an Ethernet ca-

ble (RJ-45 plug).

Select Ethernet Adapter Click the pull-down menu to

select the IP address of the router or the IP address of

the existing corporate network on which the Gateway is

installed. Click OK to save.

Replacing an existing Gateway

DL-Windows makes it easy to replace an existing Gate-

way device with a new one. Click the GW Confg button

to open the Gateway Configuration screen. Click to

highlight the Gateway in the list that you want to replace,

then click Actions, Replace Gateway with new one.

Be sure to remove power from the old Gateway. See

page 46 for the complete instructions.

Replacing a physical lock

A physical lock is currently installed on a door, is fully

enrolled in the wireless system, but needs to be re-

placed with a new lock on the same door. Proceed as

follows:

Remove the old lock from the door, and install the new

lock as per the installation instructions WI1674. Make

note of the old and new lock serial numbers and have

these numbers available when you use DL-Windows.

In DL-Windows, click the GW Confg button to open the

Gateway Configuration screen. Click to highlight the

Gateway in the list to which the old lock was assigned,

then click Tools, Delete Locks by Serial Number.

The Delete Serial Number(s) screen opens. Check the

old lock's serial number and click the Delete Selected

Serial Number(s) button.

In the Gateway Configuration screen, click the Number

of Locks to Discover pull-down list and select a number

of locks that you want to detect; in this case, you can se-

lect "1" because you are only adding one new lock to the

system. Click the Discover Locks On Selected Gate-

way button to initiate the search.

A popup screen entitled "Discovered 1 Locks" will ap-

pear, indicating the serial number of the new lock, the

signal strength and the lock model of this newly installed

lock.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 67 68

Komentáře k této Příručce

Žádné komentáře

Alarm Lock ETPLN Uživatelská příručka Strana 22

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Alarm Lock ETPLN